Showing results: 1906 - 1920 of 2617 items found.
-
4167 MF -
Standard Electric Works Co., Ltd
● High Quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Test test leads are supplied as standard accessories for simplified two-wire measuring system.● Two insulation test voltages(DC) : 250V and 500V.● Alternation voltage measurement.● Battery life indicator.● Fuse protected.
-
1620 ER -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures earth resistance in three ranges : 40Ω, 400Ω, 4kΩ.● Capable of measuring earth voltage.● 3 ¾ digit (4000 counts).● LCD backlight display.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Data hold function.● Relative function.● Auto power-off function.● Low battery indication.● Calibration performed with supplied test leads.
-
185 LCT -
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
Y1800A -
Keysight Technologies
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
-
HR8006 -
HighReach Measuring & Controlling System Co.,Ltd
At The HR8006 Universal Digital Water Level gauge IS AN the INPUT of the type Water Level Measuring Instrument with A Stainless Steel Full-Sealed Structure, Which Greatly Improves at The Reliability of at The Whole Machine and CAN BE PUT INTO at The Water for A Long Time. Since at The Circuit uses Low -power devices, the power consumption of the whole device is very low, and it is about 4 mA at full speed. This feature is very useful in situations where battery power is required.
-
KM-20-10 / KM-20-20 -
Kusam Electrical Industries Limited
• Dual channels / dual traces, X-Y mode• 6” display, high brightness oscilloscope tube• High sensitivity triggering, upto 1mV / division clearer displaythan ordinary oscilloscope.• TV synchronous separation circuit to observe stable TV signal.• Triggering mode : AUTO / NORM / AV-V / AV-H• Vertical : ALT / CHOP / ADDX-x10 / Y-x5; Polarity reversal; CH1 Sync output• Power Supply : AC 220V ADN (110V optional)
-
Model KM LUX 99 -
Kusam Electrical Industries Limited
• Precise & easy readout.• High accuracy in measuring.• LSI - circuit use provides high reliability & durability.• Permits a wide range of light measurements.• Low Battery Indication.• Auto zero adjust.• Compact, light-weight, & excellent operation.• LCD display can clearly read out even in High Ambient Light• LCD display provides low power consumption.• Separate LIGHT SENSOR allows user take measurements at an optimum position.
-
F1V04 -
Beijing SANKI Petroleum Technology Co., Ltd.
The main board issues a start signal and a low voltage signal (12v) for opening the electromagnetic valve, which are converted into strong voltage signals (220 VAC) to drive the electromagnetic valve (380 VAC) and the motor in our fuel dispensers system, thus completing the function of conversion from weak voltage power to strong voltage power. The control board circuit isolates high voltage interference signals via photoelectrical isolating components.
-
Virginia Panel Corporation
VPC's iCon EMI connector features all of the same benefits as the iCon, but with Electro-Magnetic Interference Protection. "Mate First, Break Last" feature connects the earth ground circuit. Earth ground terminal prevents user shock and injury. Threaded metal coupling adapter on ITA allows for max cable bundle of 1.50 sq. in. Fully wired connectors are available with flying leads.*Note: Click here for info on ITA backshells and conduits.
-
DT3 -
North Atlantic Industries
The DT3 module (the enhanced version) feature 4 independent, high current, isolated, programmable channels that can be used for input voltage measurements (±100 V), or as a bi-directional current switch (up to 3 A per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
LX-08 -
Link Instruments
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
-
6000 Series Rotary Handler -
Circuit Check, Inc.
Rotary table handlers are an excellent choice for PCBA or product – level test, programming, part marking, automatic part rejecting, and vision inspection in order to satisfy manufacturing applications that require high throughput. Rotary table based systems used in production can also help reduce the impact of load and unload times for the operator, because the device-under-test (DUT) automatically moves to the next cell within the station as each DUT is loaded. Circuit Check’s 6000 series handlers are modular, scalable and flexible, supporting high-mix and high-volume production needs. A common application example is to configure a 6000 series as a rotary station to perform simultaneous PCBA bar code scanning, testing, programming and marking, in a pipe-line process which improves throughput requirements. The 6000 series handlers leverage Circuit Check’s unique quick-change fixture drop-in technologies to allow for station modularity and scalability. Production line flexibility is achieved because the 6000 series handler is software and hardware agnostic, enabling adaptability to a variety of applications, and is limited only by the number of stations.
-
HR9100E -
HighReach Measuring & Controlling System Co.,Ltd
1. Safety / use of die-cast aluminum alloy waterproof, explosion-proof shell; the explosion-proof grade of the instrument reaches Exd (ia) IIBT4 2. stable and reliable / we choose high-quality module key components from the power supply Part of The Circuit Design Stable and Reliable Devices CAN Completely Replace imported Instruments. 3. Patented Technology / Ultrasonic Intelligent Software CAN with Carry OUT Intelligent echo Analysis, the without the any the debugging and OTHER Special Steps, the this Technology has The function of Dynamic Thinking, Dynamic Analysis 4. High precision / sound wave intelligent patent technology owned by our company, so that The accuracy of the ultrasonic level gauge is greatly improved, the liquid level accuracy reaches 0.3%, it can resist various interference waves, the failure rate is low, the installation is easy, and the maintenance is easy. The instrument is a non-contact instrument and does not directly contact with liquid. Users can use this manual to calibrate the instrument. 6. The protection level of multiple protection/instrument reaches IP65; all output and input lines have lightning protection and short circuit protection.
-
FlatScope -
Werth Inc.
Perfect for the measurement of larger 2D profiles (e.g.),films, circuit boards, laser cut and stamped parts large and smallMachine design with the image processing sensor under the glass plate, eliminates time-consuming focusing as the workpiece is always in the correct distance to the opticsIn raster scanning mode the machine also quickly captures the selected measurement range completelyAll geometric features are then evaluated automatically in the imageQuick dimensional measurements in the scanned image and automatic gaging with ToleranceFit® comparisons
-
QQA Series -
Semiconductor Circuits, Inc.
The QQA series features the latest in MOSFET design, state of the art surface mount technology, and offers a 4:1 ultra-wide input range, and efficiencies greater than 80% (typ). Features include continuous short circuit protection, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. All models are packaged in a six-sided shielded miniature case measuring only 1.0” x 2.0” x 0.4” high.
